Plástica dos Fios Sealing Thermal is an intensive treatment that reduces the volume, eliminates frizz and provides smooth hair strands and controlled by up to 3 months. Nourishes and deeply hydrates the hair strands in addition to an incredible shine and strengthen the structure, preventing the breakdown.
Contain
Plástica dos Fios Sealing Thermal Step 2 - 1 liter: 2 unit.
Action
Treatment consists of Arginine, acai extract and Acetic Acid (ph acid).
Acai Extract: Rich in nutrients such as vitamins, sugars Essential oils and emollients. Its antioxidant action and protective promotes a complete regeneration of the strands, moisturizing them in an efficient and sustained manner.
Amino acids: balance the structure of the hair strands of the aggressions caused by excessive use of dryers and flat irons. Increases its suppleness and elasticity, leaving the hair softer and extremely easy to comb.
Application:
Requirements: silicone gloves, dryer, board, plastic tabs, comb, brush and a plastic container.
1- Wash your hair with the Pre-Treatment Shampoo, massaging it until it forms a foam. Wash twice in case of virgin, very resistant or very dirty hair. Leave on for 5 minutes and rinse thoroughly. Warning: do not rub the scalp.
2- Dry the hair in 80% with the dryer and the help of the fingers.
3- Separate the hair in 6 parts (a vertical line separating the hair in two strands - right and left - and 3 horizontal sessions - nape, middle and front from the ears). Tie each session into a bun with a hair clip.
4- Pour 20 to 40ml of the Thermal Seal in a container and put on the silicone gloves.
5- Begin to apply in a session of the nape of the neck with the help of the brush. Apply two fingers of the root to the base of the session and pull the product to the tips with the comb. Make sure the product is on all strands.
6- Repeat the procedure with the session on the side.
7- With the dryer in the cold jet, dry the two sections in 100%. It is important to dry two sessions at a time with the cold jet. This prevents the formation of smoke and prevents the product from evaporating without having any effect.
8- Repeat the procedure from 5 to 7 in the two central sessions of the hair, one at a time.
9- Finally, repeat the procedure from 5 to 7 in the two frontal sessions of the hair, drying the strands backwards. It is important that neither the wind of the dryer nor the session with the product come into contact with the face.
10- Time to straighten! In blonde, damaged or chemical hair, the temperature of the flat iron should not exceed 200°C. On normal, virgin or temperature resistant hair, the temperature should be 230°C.
11- Divide the hair again into parts using hair clips. Separate a thin and linear session and straighten the length (without the ends) of the session 10 times ( flat iron at 200°C) or 7 times ( flat iron at 230°C).
12- Straighten the ends (without the length) of the hair up to 4 times ( flat iron at 200°C) or 2 times ( flat iron at 230°C). In this way you avoid the artificial straight effect on the ends.
13- Repeat this process (step 11 and 12) for all hair sessions. The flat iron straight to the scalp naturally straightens the strands from the root.
14- After all sessions, rinse the hair well.
15- Apply the Restorative Mask on the strands, gently massaging the strands. Leave it on for 5 minutes and rinse again.
16- Dry the hair with the dryer.
Note: In the case of relaxed or straightened hair, apply the Plastica dos Fios Thermal Sealing after the chemical process. In case of color tinting or tonalization, apply the Plastica dos Fios Thermal Sealing two days before or after the color tinting, to better fix the color pigments in the strands.
We recommend that you use this treatment with the help of a professional.
Result
Naturally straight hair without frizz, stronger, repaired and with an incredible brightness for up to 3 months!
